Garage door and other types of metal doors Home theaters, including speaker cabinets, and projector housing Below are a few examples of other uses for LizardSkin products: Both Sound Control and Ceramic Insulation can be used around your home, garage, or commercial workspace, anywhere you want to reduce heat and noise. LizardSkin’s ability to insulate and dampen vibration is great for cars and trucks, but there are many more uses on all types of vehicles and trailers. Run water through the sprayer after you have finished application so that the sprayer doesn’t clog on the next coat or the next time you spray. If you aren’t able to, at least place the equipment into a bucket of water for easy cleaning later. Make sure to clean all equipment thoroughly immediately after use. Once the Sound Control has cured, just repeat the above steps taking the varying air pressures required for each product into account. Do not force cure by aiming a heat source at the wet coating. It must air dry. The warmer it is, the quicker the coating will dry. If you are applying both products, make sure that the Sound Control has cured completely (24 hours at 70✯) before applying Ceramic Insulation.
LIZARDSKIN SOUND CONTROL MANUAL
See the instruction manual for more detail. Use the 90º tip for hard to reach places such as door skins.
Once the first coat is dry to the touch (between 30 and 60 minutes) follow with the second coat. Usually two passes gives you the desired thickness of product per coat (20 mils or 0.5 mm.) Measure using the Mil Thickness Gauge supplied in the Application Kit. Spray evenly across the substrate with a sweeping motion. LizardSkin Ceramic Insulation – 50-70 PSI Once you have a good fan, begin spraying your substrate holding the sprayer tip approximately 6-9 inches away from substrate. Just pump it a few times and adjust the nozzle and air pressure accordingly. Most find it works well from here, and usually only requires small adjustments from this point.Īttach the cup to the sprayer and test the fan and pressure by spraying it at a piece of cardboard or into a trashcan. This is a good starting point that will minimize the tip adjustment time. Turn the tip inward until it stops then back out the tip with 2 (two) turns out. Holding the bucket about 12-16 inches above the cup will allow the product to flow down to a narrow ribbon, allowing for a clean pour.Īdjust the tip of the sprayer. Pick up the bucket and pour it into the cup. Remove the cup from the sprayer and place it on something to protect your garage floor in case you spill. The product should be the consistency of a milkshake, which shouldn’t take longer than 2 minutes. Use the drill and mixing paddle to mix the contents of the bucket. When using both products (stacking) ALWAYS apply Sound Control FIRST then apply Ceramic Insulation on top. Open the lid of the product you want to apply. This is a quick summary on the application of LizardSkin products.
Once you’ve done all of the necessary prep work, you’re ready to spray. With LizardSkin, there is no need to measure and cut insulation precisely to size, and there is no risk of cutting your hands and bleeding. A typical mat product installation can take 35+ hours, whereas spray-on insulation requires only 8 hours. Traditional mat products are known for being more labor-intensive and costly than spray-on insulation. It can also be sanded and painted to your desired body color. Never cut and paste mat products again! With LizardSkin there are NO GAPS, NO SEAMS, NO SCISSORS AND NO SWEAT! LizardSkin’s easy-to-apply, spray-on application is environmentally safe and can be cleaned with soap and water. LizardSkin’s ability to be sprayed on allows the customer to effectively insulate any type of vehicle without the tediousness and waste associated with mat-style products The company’s experience in the industrial, marine and commercial fields have paved the way for LizardSkin’s unique ability to keep out heat and noise in a thin, coating format. Mascoat, the leader in insulating coatings, manufactures LizardSkin coatings. All products are available for purchase via our online store. Our product lines include: Ceramic Insulation, Sound Control and TopCoat and we also offer the SuperPro Application Kit to simplify the applications of these products.
Since LizardSkin came on the market, thousands of auto enthusiasts around the world have applied the coatings and enjoyed cooler, quieter rides. LizardSkin coatings are a fast, easy way to reduce the amount of heat and noise that enters the interior of your vehicle.
0 kommentar(er)
